How To Make A Bong Without Foil?

11/13/2024
LOOKAH

How To Make A Bong Without Foil

If you want to make a homemade bong but don't have aluminum foil, don't worry!

We're here to show you how to make one without foil.

In this article, we’ll guide you through four simple methods to craft a bong or pipe using common household items.

Whether you're out of supplies or just looking for a creative solution, you’ll be able to enjoy a smoke session in no time.

Let's get started!

The Anatomy Of A Bong

Before we dive into the steps of creating your bong without foil, it's essential to understand the basic parts of a bong:

Chamber: This holds the water that helps cool and filter the smoke as it passes through.

Downstem: This tube or pipe, connected to the bowl, allows smoke to travel down into the chamber, through the water, and then up to the mouthpiece.

Bowl: This is where herbs are placed and ignited. The heat from the flame causes the herbs to burn and produce smoke.

Mouthpiece: This is typically the neck of the bong or another opening where the user inhales the filtered smoke into their lungs.

1. Mason Jar Bong

Mason-Jar-Bong

Step 1. Prepare the Mason Jar

Clean the Jar: Remove any stickers or labels by soaking the jar in warm soapy water. Use a scrub brush to remove the adhesive.

Inspect the Lid: If the lid has a rubber seal, carefully remove it to prevent unwanted smells.

Drill Holes: Use a drill with a diamond tip to create two holes in the lid. One should fit your downstem snugly, and the other should be smaller for the mouthpiece. Smooth any rough edges with sandpaper.

Step 2. Make the Downstem

Materials Needed:

  • A metal tube or pen shaft
  • Rubber grommet or silicone seal
  • Drill with a small bit
  • Lighter

Instructions:

Drill several small holes near one end of the metal tube for better airflow.

Attach a rubber grommet or silicone seal to the other end.

Insert the downstem into the hole on the lid and secure it firmly.

Step 3. Assemble the Bong

Insert the Downstem: Place the downstem into the mason jar lid. Ensure a snug fit without forcing it.

Seal the Downstem: Use a rubber grommet or silicone seal to create an airtight seal around the downstem.

Attach the Bowl: Screw the bowl piece onto the top of the downstem.

Fill with Water: Add water to the jar, covering the bottom of the downstem. Ensure it’s enough to filter the smoke but not too much to cause leaks.

Step 4. Test for Air Tightness

Cover the mouthpiece and downstem holes.

Inhale gently and check for air bubbles.

If you see bubbles, adjust the seal to ensure airtightness.

2. Apple Bong

apple-bong

Step 1. Preparing the Apple

Start by removing the stem from the top of the apple, twisting, and pulling it out completely.

This will create a natural bowl where you can pack your weed.

Step 2. Crafting the Bowl

Use a sharp tool to carefully carve a hole straight through the center of the apple.

This hole will be the main channel for the smoke to travel through.

Step 3. Creating the Mouthpiece and Carb

Mouthpiece: Use a toothpick or similar tool to make a few holes in the top of the apple (where the stem was). These should intersect with the central hole you just carved.

Carb: Poke another hole in the side of the apple. This should also intersect with the central hole. The carb will help control airflow and clear the smoke when you inhale.

Step 4. Adding the Percolator

To make your apple bong more effective, use your tool to carve a small reservoir in the center of the apple’s tunnel.

This will help the smoke circulate better, and you can add small holes to improve airflow and prevent the weed from falling into the apple.

Step 5. Packing the Bowl

Stuff some weed into the bowl at the top of the apple.

Don't overpack it—this can restrict airflow.

If you want to avoid small pieces falling into the apple, use a small piece of foil or glass as a screen.

Step 6. Lighting and Inhaling

Place the mouthpiece hole to your lips and cover the carb hole with your finger.

Light the weed in the bowl while inhaling gently through the mouthpiece.

Tilt the apple at a 45-degree angle to help the smoke filter through the percolator and deliver smooth, fruity hits.

Enjoy your apple bong responsibly!

3. Beer Can Bong

can-bong

Step 1. Rinse the Can

Thoroughly rinse the soda can to remove any sticky residue.

Step 2. Create the Bowl

Pick a spot about halfway or two-thirds down the can and poke small holes in a circular pattern.

This will form the bowl for your smoking material.

Make the holes on the side opposite the opening designed for drinking.

Step 3. Make the Carb Hole

Poke a hole in the bottom of the can to serve as a carb hole.

Step 4. Shape the Bowl

Gently bend the can to create a small indent where the holes are.

This will help keep the weed in place while you inhale.

Step 5. Pack and Light

Place your weed in the holes, light it, and inhale through the mouthpiece.

Enjoy your makeshift pipe!

4. Pen Pipe

Pen-Pipe

Step 1. Remove the Metal Tip

Take off the metal tip of the pen, which is cone-shaped with a wide hole on one end and a narrower hole on the other.

This will act as your bowl where you pack the weed.

If you can't remove the tip, the pen won’t work for this pipe.

Step 2. Open the Pen

Flip the pen around and use your thumbnail to apply pressure on the edge of the cap to pop it off.

If it’s a screw-on cap, twist it to remove it.

Use a butter knife to pry it off if it’s stuck.

Step 3. Remove the Ink

Take out the ink cartridge from inside the pen and discard it.

This leaves you with an empty pen tube, which will serve as the smoke’s tunnel.

Step 4. Attach the Metal Tip

Insert the narrower end of the metal tip into the open end of the pen tube, pushing it in firmly so it stays in place. Make sure there are no air leaks.

If the tip doesn't stay in, tape it securely. Be careful not to push too hard to avoid breaking the pen.

Step 5. Pack the Bowl

Fill the metal tip with coarser pieces of weed finely ground weed might fall through the holes.

Step 6. Light and Inhale

Place your mouth on the open end of the pen tube, light the weed in the metal tip, and inhale.

If the metal tip isn't secure, you might not get proper airflow, and the bowl could fall out during the hit.

Enjoy your homemade pen pipe!

Conclusion

You don’t need to be an engineer to build a homemade bong just a bit of creativity and patience!

The fun part is that you can use almost anything around the house to make one.

We hope these ideas have sparked your imagination!

Enjoy, and feel free to share photos of your homemade masterpieces or any unique bong-building tips you come up with!