Taper Mouth Glass Pipe

The blue flat mouth glass pipeis a sleek and stylish smoking accessory.

This pipe features a beautiful blue color that is both eye-catching and soothing. The flat mouth design provides a comfortable and efficient smoking experience.

Crafted from glass, it offers a smooth smoking sensation. The quality material ensures durability, so you can enjoy this pipe for a long time.

The blue hue gives the pipe a modern and trendy look. Whether you're using it for a relaxing smoke session or adding it to your collection, the blue flat mouth glass pipe is sure to impress.

How To Use A Pipe?

Step 1: Prepare the Cannabis

Use a grinder to break up your cannabis buds into a medium consistency. Aim for a texture that is not too fine (to prevent blocking the pipe) and not too coarse (for even burning). It should be similar to coarse sand to allow for optimal airflow and even burning.

Step 2: Pack the Bowl

Gently place the ground cannabis into the bowl of the pipe. Do not pack it too tightly as this can restrict airflow. Fill the bowl loosely to about three-quarters full. You can use your finger or a tamping toolto lightly press the cannabis to create a slightly firm but still airy pack.

Step 3: Cover the Carb

Many pipes have a carburetor, or carb, which is a small hole on the side. Cover this hole with your thumb or index finger. The carb helps regulate airflow and allows you to clear the smoke from the pipe.

Step 4: Light the Bowl

Hold the pipe to your mouth and create a seal with your lips. Use a lighter or hemp wick to apply flame to just a corner of the packed bowl. This technique, known as “cornering,” helps preserve the fresh taste of the cannabis. As you light, begin to inhale slowly and steadily.

Step 5: Release the Carb Hole

Once you've drawn enough smoke into the chamber, stop lighting and remove your finger from the carb hole while continuing to inhale. This rush of fresh air will push the remaining smoke from the chamber into your lungs.

How To Clean A Pipe?

Step 1: Prepare Your Bong for Cleaning

Before you begin cleaning your bong, clean out the bowl and empty any water. Then, rinse the bong with warm or hot water to loosen any debris, resin, or other buildup.

Step 2: Add Salt and Alcohol

Next, fill your bong or pipe with salt, and add enough isopropyl rubbing alcohol to cover the bong completely. Use a funnel if needed to contain the mess. For best results, use 91% isopropyl alcohol, but 70% will also work.

You can also place the glass piece in a Ziploc-style bag zip it up and shake the bag. Be careful the bag does not rip, especially with the sand. You might need to replace the alcohol more than once if the piece is especially dirty. However, this method also works very well, especially for glass spoon-style pipe or other smaller style pieces.

Step 3: Shake Vigorously

Shake the bong or pipe vigorously for 20 seconds or more if needed, making sure to get the salt and alcohol into all the nooks and crannies. Repeat this process as needed until the bong looks clean. As the alcohol gets dirty and turns black, dump it out and replace it with fresh alcohol and salt. Repeat the shaking process.  

Step 4: Spot Clean Exterior

You will need to spot-clean any exterior areas that need special attention. Often, the bottom or underneath of the pipe, bong,or bubbler can be one of those pesky areas covered in resin.  If it’s really caked up on the bottom exterior, try heating the resin spots with a lighter for 2-3 seconds and then using a bit of alcohol on a paper towel to rub it off.

Step 5: Rinse Thoroughly

Once your bong looks clean, rinse it thoroughly with hot water to remove any remaining salt and alcohol residue. Use a paper clip or straw brush to get into the harder-to-reach areas as needed.

Step 6: Make It Shine With Some Dish Soap

To give your bong an extra shine, you can put a tiny dab of dish soap into and onto the exterior of the bong. Rub it all over the exterior. Then rinse it off with warm water. This will also help to remove any lingering odors and make it sparkle.

Step 7: Clean the Sink Area

Finally, it is recommended to use alcohol to clean the sink area of any resin or mess that was created during the cleaning process.

Specification

• Product Size:3.27 inch
• Color： Blue
• Material:Borosilicate Glass
• Net Weight:20 g

Products include

• 1x Flat Mouth Glass Pipe